When a tablet screen breaks, check two things: whether the picture is still clear (if it is, the LCD is probably fine) and whether touch still works everywhere (if it does not, the glass digitiser is damaged). On many budget and older tablets, such as standard iPads up to the 9th generation and many Samsung Galaxy Tab A models, the glass digitiser and the LCD are separate parts, so cracked glass with a perfect picture needs only a new digitiser. On laminated tablets, such as iPad Air 2 and later, iPad Pro and most premium Android tablets, the glass and display are bonded together and must be replaced as one assembly. This guide shows how to diagnose the damage, which part to buy, what drives the cost, and how the repair is done.
The parts of a tablet screen
- Glass digitiser (touch screen): the outer glass with a touch-sensitive layer. If it cracks, touch may still work, partly work or fail.
- LCD or OLED display: the panel underneath that produces the image. Damage shows as black blotches, coloured lines, bleeding ink patterns or no picture.
- Laminated assembly: on many tablets the glass and display are bonded with no air gap. They are sold and replaced together.
Step 1: diagnose what is broken
| What you see | Likely damaged part | What to replace |
|---|---|---|
| Cracked glass, clear picture, touch works | Glass digitiser only | Digitiser (if separate) or full assembly (if laminated) |
| Cracked glass, clear picture, touch dead or jumping | Digitiser | Digitiser (if separate) or full assembly |
| Glass intact, black blotches or lines | LCD or OLED panel | LCD (if separate) or full assembly |
| Cracked glass and black blotches or lines | Both | Both parts, or full assembly |
| Screen black, but tablet makes sounds or connects to a computer | Display, backlight or connector | Check connection, then LCD |
| No picture, no sound, no charging light | Power, battery or board | Diagnose power before buying a screen |
| Touch acting on its own ("ghost touch") with no cracks | Digitiser fault, charger interference or software | Test with another charger and after a restart first |
A useful test for a black screen: shine a torch at the display at an angle. If you can faintly see icons, the LCD is working but the backlight is not, which often points to the LCD assembly or its connector.
Which tablets have separate glass and LCD?
This is the single biggest factor in what you need to buy.
Apple iPad
- Separate glass and LCD: standard iPads from the iPad 2 to the iPad 9th generation (10.2-inch, 2021), the first iPad Air (2013), and iPad mini 1, 2 and 3.
- Laminated (replace together): iPad Air 2 and later, iPad mini 4 and later, all iPad Pro models, and the iPad 10th generation and later.
Our iPad parts collection and model collections such as the iPad 10.2 9th generation parts and iPad Air 2 parts list what fits each model.
Samsung Galaxy Tab
Many Galaxy Tab A and Tab E models use a separate touch digitiser and LCD, while Galaxy Tab S models with AMOLED screens generally use a bonded display assembly. Check the parts listing for your exact model number (for example SM-T580, SM-T590 or SM-T290), which is printed on the back of the tablet or in Settings, About tablet. See our model collections such as Galaxy Tab A 10.1 (2016) parts, Galaxy Tab A 10.5 (2018) parts and Galaxy Tab A 8.0 (2019) parts.
Other Android tablets
Budget tablets from Lenovo, Amazon, Huawei and others vary. Many budget models have separate digitisers; some newer ones are laminated. The parts listing for the exact model is the reliable guide.
Glass only vs full assembly: pros and cons
| Option | Advantages | Disadvantages |
|---|---|---|
| Glass digitiser only (non-laminated tablets) | Cheaper part; keeps the working LCD | Old adhesive must be cleaned thoroughly; risk of damaging the LCD while removing broken glass |
| Full screen assembly | Fixes glass and display in one go; usually quicker to fit | Higher part cost |
| Separate glass refurbishing on laminated screens | Possible for specialist shops with lamination equipment | Not a DIY repair; needs separation and re-lamination machines |
How much does a tablet screen replacement cost?
We do not publish a single price, because it depends heavily on the tablet. The main cost drivers are:
- Laminated or separate: laminated assemblies cost more than a digitiser alone.
- Display type: OLED and high-resolution displays on premium tablets cost more than basic LCDs.
- Size: larger panels cost more.
- Part grade: OEM standard parts generally cost more than budget aftermarket parts but offer closer colour, brightness and touch response.
- Labour: if a shop fits it, labour is added. Glass-only repairs on tablets with separate digitisers can take longer because of adhesive cleaning.
- Manufacturer repair: Apple and Samsung offer official repairs; see Apple's iPad repair page and Samsung UK repair support for their current pricing and options.
Before paying for a repair, compare the cost with the tablet's value. For an old, low-cost tablet, a screen repair can approach the price of a replacement tablet.
Tools and materials
- Heat source: heat pad, hot plate or heat gun on a controlled setting.
- Suction cups and plastic opening picks.
- Thin plastic cards for cutting through adhesive.
- Safety glasses and cut-resistant gloves (broken tablet glass splinters easily).
- Packing tape to cover cracked glass before you start, which holds shards together.
- Isopropyl alcohol (90% or higher) for cleaning old adhesive.
- Adhesive strips or a suitable screen adhesive for refitting.
- Small screwdrivers for internal shields on some models.
Our repair tools and adhesive collection covers the essentials. For bonding screen edges and frames, we sell a black multifunction adhesive:
The 50mL T7000 black glue is £3.49 (price read from our store on 15 October 2026). It is a black, multipurpose adhesive often used around screen edges and frames, where a black bead is less visible. Follow the product's instructions, apply sparingly, keep it away from the display's active area and internal components, and allow it to cure fully before using the tablet.
How a tablet screen replacement works: overview
Procedures vary widely between models. Use a model-specific guide; iFixit has guides for many iPad and Android tablet models. The general process is:
- Back up and power off.
- Tape over the cracked glass to hold fragments together.
- Heat the edges evenly to soften the adhesive.
- Lift the glass with a suction cup or, if it is shattered, start with a pick at an intact corner. Work slowly around the edge with picks and plastic cards.
- Watch for cables. On many tablets the digitiser cable is near one edge; on iPads, the home button and antenna cables sit close to the bottom. Do not slide picks deeply in those areas.
- Disconnect the battery as soon as you can reach it, before unplugging display cables.
- Separate the LCD if it is a separate part. Lift it out carefully and set it aside on a clean, soft surface if you are reusing it.
- Remove every piece of old glass and adhesive from the frame. Leftover shards or uneven adhesive stop the new glass sitting flat.
- Transfer small parts such as the home button, camera bracket or speaker mesh if the new part does not include them.
- Connect and test the new parts before sealing: check display, touch across the whole surface, and buttons.
- Apply new adhesive and press the glass into place evenly. Clamp or weigh it down gently while it sets.
After the repair: test checklist
- Draw slowly across the whole screen in a drawing or notes app, including all four edges and corners, to find any dead touch zones.
- Check the display on a plain white and a plain black image for bright spots, dark patches, lines or light leaking at the edges.
- Test the home button or fingerprint sensor, volume and power buttons.
- Rotate the tablet to check the auto-rotate sensor.
- Test the front camera, speakers and microphone with a video call.
- Charge to full and check the tablet holds charge normally.
- Leave the tablet face down on a soft cloth for a few hours if you used liquid adhesive, then check the glass is still seated flat.
Repair or replace the tablet?
A screen repair is usually worthwhile on a tablet that still receives software updates, has a healthy battery and meets your needs. It is harder to justify on an old tablet that no longer gets updates, has a worn battery, or struggles to run the apps you use, because you may need to replace it soon anyway. Check the tablet's software status in its settings, consider the battery condition, and compare the total repair cost with the price of a suitable replacement tablet before deciding.
When to use a repair shop instead
- The glass is shattered into small pieces, which makes removal slow and risky.
- The tablet is laminated and you want to replace only the glass.
- The tablet has a fingerprint sensor or Face ID-style components that are paired to the board.
- The battery is swollen, which is a safety risk.
- You need the tablet back quickly and reliably.
Our guide to iPad screen repair near you explains what to look for in a repair service.
Fixing a tablet screen that is not working (but not cracked)
- Force restart. On iPads with a home button, hold the home and top buttons; on newer iPads, press volume up, volume down, then hold the top button. On Android tablets, hold power and volume down.
- Remove the case and screen protector, which can cause unresponsive or phantom touches.
- Clean the screen; moisture or grease affects touch.
- Unplug the charger. Poor chargers can cause ghost touches while charging.
- Update the software.
- Connect to a computer if the screen is black, to see whether the tablet is running.
If none of these help, the digitiser or display is likely faulty and the diagnosis table above applies.
Common mistakes
- Buying a digitiser for a laminated tablet. It will not fit.
- Ordering by tablet name instead of model number. Galaxy Tab models in particular have many similar variants.
- Not disconnecting the battery before unplugging the display.
- Cutting through display cables with picks inserted too deep.
- Leaving old adhesive or glass fragments on the frame.
- Getting glue on the display area or inside the tablet.
- Skipping safety glasses. Tablet glass splinters are sharp.
Protecting a repaired tablet screen
Fit a tempered glass screen protector and a case with a raised edge or folio cover. Most tablet screens break from drops onto corners, so a case with reinforced corners does much of the work. For children's tablets, a thick foam case is the best investment.
For related reading, our guide to LCD displays explains how LCD panels work, and our phone screen fixers guide covers choosing a repairer.
Frequently asked questions
How do I fix a broken tablet screen?
Diagnose whether the glass, the display or both are damaged, check whether your tablet's glass and display are separate or laminated, then replace the correct part using a model-specific guide or a repair shop.
How do I fix a tablet screen crack?
A crack in the glass needs a new digitiser (on tablets with separate glass) or a full screen assembly (on laminated tablets). Screen protectors and resin kits do not restore cracked glass.
How much is a tablet screen replacement?
It depends on the model, display type, size, whether the screen is laminated, and labour. Check the parts listing for your model and compare with official repair prices.
Why is my tablet screen not working but not cracked?
It may be a software freeze, a faulty charger, a screen protector issue, a loose connector or a failed digitiser or display. Restart, remove accessories and update first.
Can I replace just the glass on an iPad?
Yes on standard iPads up to the 9th generation, the first iPad Air (2013) and iPad mini 1 to 3. On laminated models, the glass and display are replaced together.
Next step
Use the diagnosis table to decide which part has failed, find your tablet's model number, and check whether its glass and display are separate. Then order the matching part from our model collections, along with adhesive and opening tools, so you can complete the repair in one sitting.

