A Huawei P30 Pro screen replacement costs £62.00 for the display assembly at The Repair Plus (listed for models VOG-L09 and VOG-L29, checked 15 October 2026), plus labour if a shop fits it. The P30 Pro has a 6.47-inch curved display with an in-display fingerprint sensor, so this is one of the harder screen repairs: you usually open the phone from the glass back to disconnect the battery and display, then heat and lift the curved screen from the front. Plan two hours for a careful first attempt, or use a repair shop if you have not worked with curved screens before. This guide explains how to tell whether you need a new screen, what to check in a replacement, the real cost of each repair route and the main steps.
Huawei P30 Pro screen: key facts
| Detail | Huawei P30 Pro |
|---|---|
| Screen size | 6.47 inches, curved edges |
| Model codes | VOG-L09, VOG-L29 (also check VOG-L04 listings separately) |
| Fingerprint | In-display sensor |
| Earpiece | Sound is produced through the display rather than a separate earpiece grille |
| Access | Usually through the glass back first, then the front |
| Difficulty | Advanced |
| Replacement display price | £62.00 (The Repair Plus, 15 October 2026) |
The P30 Pro and the standard P30 use different screens. Check your model code under Settings > About phone. Parts for the smaller phone are in our Huawei P30 collection.
How much does it cost to replace a Huawei P30 Pro screen?
The display assembly costs £62.00 at The Repair Plus (checked 15 October 2026). A DIY repair adds back-glass adhesive, screen adhesive and tools; a repair shop adds labour, which is higher than average on this model because of the curved screen; Huawei's official service charges its own price.
| Route | What you pay | Trade-offs |
|---|---|---|
| DIY | £62.00 screen plus adhesive and tools | Cheapest; curved screen and back glass need care |
| Independent repair shop | Screen plus labour | Experienced hands; ask about fingerprint support |
| Huawei official service | Huawei's price for the P30 Pro | Manufacturer parts and warranty |
We have not quoted shop or official prices because they vary. Huawei's UK support site lists official repair options for supported models.
Do you need a new screen? Diagnosing the damage
| Symptom | Likely cause | Fix |
|---|---|---|
| Cracked glass, picture and touch fine | Front glass | Screen assembly (glass is bonded to the panel) |
| Green or purple lines, black blotches | Display panel damaged | Screen assembly |
| Touch dead in areas or ghost touches | Digitiser | Screen assembly |
| Black screen, phone rings and vibrates | Display or connector | Check connector; then screen |
| Fingerprint sensor stopped working after a drop | Display or sensor | Inspect; may need the screen |
| Quiet or muffled calls | Display-based earpiece affected | Often fixed by a new screen |
On the P30 Pro, the front glass is bonded to the display, so a cracked glass is fixed by replacing the whole assembly. Glass-only refurbishment requires specialist lamination equipment.
What to check in a replacement P30 Pro screen
Replacement displays for the P30 Pro vary, and the differences matter more than on most phones because of the in-display fingerprint sensor and curved glass.
- Fingerprint support: in-display fingerprint sensors work through OLED panels. Some replacement panels, particularly non-OLED types, do not support the in-display sensor. Read the listing carefully, and ask the seller if it is not stated.
- Panel type and quality: an OEM standard OLED gives the closest match to the factory colours, brightness and battery use.
- Frame: some assemblies come with a new frame fitted, which makes fitting easier; others are the display only.
- Model compatibility: our listing covers VOG-L09 and VOG-L29.
Many buyers want a display identical to the factory part. What matters is that the replacement is built to the factory specification and supports the features you use; check the product description for panel and fingerprint details before buying.
Is it worth replacing a P30 Pro screen?
Often, yes. The P30 Pro's Leica-branded quad camera with periscope zoom remains impressive, and it runs Google services, which newer Huawei phones sold in the UK do not. If the phone is otherwise healthy, a screen repair keeps a capable camera phone in use. Check whether your model still receives security updates if you rely on it for banking.
It is less worthwhile if the phone also has a weak battery, damaged back glass and a faulty camera. In that case, add up all the parts first. If the battery is worn, replacing it while the phone is open saves doing the job twice; batteries for related Huawei models are in our Huawei P20 Pro and P30 Lite collections.
Preparing for the repair
Good preparation is especially important on a phone with glass on both sides. Back up photos, contacts and messages first. Clear a well-lit table, lay down a soft cloth, and keep separate dishes or areas of a magnetic mat for the back cover screws and board cover screws. If either the front or back glass is cracked, cover it with packing tape so fragments stay together during heating. Photograph each stage, particularly the routing of the display cable through the frame, because it is easy to trap the cable when closing. Have all adhesive ready before you start, so the phone is not left open longer than necessary.
The back glass: reuse or replace?
You have to remove the back glass to reach the battery and display connectors on most P30 Pro repairs, and curved back glass sometimes cracks during removal even with careful heating. If it survives intact, clean off the old adhesive and refit it with a new adhesive sheet. If it cracks, or was already damaged, fit a new back glass at the same time, which saves opening the phone again later. Always use fresh adhesive: reused adhesive leaves gaps that let in dust and moisture.
After the repair
Once the phone is sealed, check software updates under Settings > System & updates, re-enrol your fingerprint, and set screen brightness and colour preferences again if they have reset. Over the first day, watch for any lifting at the screen edges, which can mean the adhesive needs more clamping time. Keep the phone away from water for at least a day while the adhesive fully cures, and remember that a repaired phone should not be relied on for water resistance.
Tools you need
- Heat source: heat pad, hairdryer or heat gun on a low setting
- Suction cups and several thin plastic opening picks
- Phillips #00 screwdriver
- Plastic spudger and tweezers
- Back-glass adhesive and screen adhesive
- Isopropyl alcohol and lint-free cloths
- Safety glasses
Find tools and adhesive in our repair tools and adhesive collection, and compare kits in our guide to the best phone repair tool kits.
How to replace a Huawei P30 Pro screen: main steps
This is an overview for planning. The curved screen is fragile, so follow a model-specific guide and never force anything.
- Back up your data, discharge the battery below 25% and power off. Remove the SIM tray.
- Heat the back glass edges and lift it with a suction cup and picks. Work slowly; the glass is curved and bonded firmly.
- Remove the screws holding the wireless charging coil and board covers, and lift them away.
- Disconnect the battery first, then the display connector.
- Heat the front screen edges evenly. The curved edges need gentle, even heat.
- Lift the screen with a suction cup and thin picks, working from the bottom edge. Keep picks shallow so you do not damage the frame or internal components. Feed the display cable through the frame as you lift.
- Clean the frame of all old adhesive and glass fragments.
- Fit the new screen's cable through the frame and connect it to the board, then reconnect the battery.
- Test before sealing: touch across the whole curved surface, brightness, in-display fingerprint, call audio, front camera and proximity behaviour.
- Apply new screen adhesive, seat the screen and clamp gently while it bonds.
- Refit the covers and screws, then fit new back-glass adhesive and press the back into place.
- Re-enrol your fingerprint in Settings if it is supported by your new screen.
Troubleshooting after fitting
Test everything before the adhesive goes on. Most faults after a screen swap are easy to fix while the phone is still open.
- No picture: disconnect the battery, reseat the display connector firmly and evenly, reconnect and test again.
- Touch not responding near the curved edges: check the screen is fully seated in the frame and that no adhesive or debris is under the edge.
- Fingerprint not available: confirm the new panel supports the in-display sensor. If it does, re-enrol your fingerprint and update the software.
- Quiet call audio: because sound comes through the display, a poorly seated screen can sound muffled. Check the seating and the connector.
- Screen flickers or shows a tint: reseat the connector; if it persists, contact the seller before gluing.
Using a repair shop
Curved-screen repairs are where experience pays off. If you choose a shop, ask for an itemised quote, which panel type they fit, whether the in-display fingerprint will work afterwards, and what warranty covers the screen and labour. Some shops will fit a screen you have bought; ask first, because policies vary. Back up your data and remove your SIM and memory card before handing the phone over, and test fingerprint unlock and call audio before you leave.
Protecting the new screen
Curved screens are harder to protect than flat ones. Choose a case with a raised lip around the screen edge, and if you want a screen protector, use one designed for curved displays so it does not lift at the edges or interfere with the fingerprint sensor. Avoid carrying the phone in the same pocket as keys.
Common mistakes
- Buying a screen that does not support the in-display fingerprint without realising.
- Uneven heating of the curved edges, which cracks the new or old glass.
- Not disconnecting the battery before unplugging the display.
- Damaging the display cable when feeding it through the frame.
- Sealing before testing call audio and fingerprint.
- Ordering a P30 screen for a P30 Pro.
Why the P30 Pro screen is harder than most
Three design choices make this repair more demanding than a typical flat-screen phone. The curved edges mean the glass wraps around the frame, so it flexes as you lift it and cracks more easily if heated unevenly. The in-display fingerprint sensor sits beneath the panel, so the new screen must be compatible and correctly seated for it to read reliably. And the phone has no separate earpiece grille: call audio is produced through the display, so a poorly bonded screen can affect sound quality. None of this makes the repair impossible, but it rewards patience and good preparation.
Safety and disposal
Wear eye protection when handling cracked glass, and never puncture or bend the lithium-ion battery. The charity Electrical Safety First publishes battery safety advice. Old screens go to electrical waste recycling, and damaged batteries to a battery recycling point, as GOV.UK's waste batteries guidance explains.
Frequently asked questions
How much is a Huawei P30 Pro screen?
The replacement display assembly is £62.00 at The Repair Plus (checked 15 October 2026). Labour is extra if a shop fits it.
How do I replace a Huawei P30 Pro screen?
Remove the back glass, disconnect the battery and display, heat and lift the curved screen from the front, fit the new screen, test it, then reseal the screen and back with new adhesive.
Can a P30 Pro cracked screen be fixed without replacing the display?
Not at home. The glass is bonded to the display panel, so DIY repairs replace the full assembly. Glass-only refurbishment needs specialist equipment.
Will the fingerprint sensor work with a new screen?
It depends on the replacement panel. In-display fingerprint sensors need a compatible panel, so check the listing or ask the seller before buying.
How big is the Huawei P30 Pro screen?
The P30 Pro has a 6.47-inch curved display, larger than the standard P30, so the two phones use different replacement screens.
Next step
Confirm your model code, decide whether to fit the screen yourself or use a repairer, and order the display with adhesive. Browse all spares in our Huawei P30 Pro collection.

